Incinerator

Product Details:

 

AVAILABLE LOADING CAPACITY: 50, 100, 150, 200, 500, 1000 Napkins/day

Additional Information:

• Item Code: TZ-230
• Packaging Details: Box Carton

Product Details:

ITEM CODE: JKA-230BM

BIO-MEDICAL HOSPITAL INCINERATOR

DESIGN:
The design is based on the guidelines set by Central Pollution Control Board (CPCB)-India and normally adopted by military installation all over the country and worldwide. The Efficient power is supplied by electricity as well as oil burners for larger installation.The incinerator combustion chamber is designed for easy maintenance of all internal parts including refractory and isolation.

SPECIFICATIONS:

• Combustion efficiency 99%.
• Combustion Chamber : Dual Chamber
• Temperature of primary chamber is up to 1000°C and the secondary chamber is up to 1450°C.
• The secondary chamber gas residence time at is two seconds.
• Power Requirement: Diesel, Electrical

AVAILABLE LOADING CAPACITY : 10/25/50/100/150/200/250/500 Kg/Hr.

** Note: The content of the product and specification are subject to change without prior notice for continuous improvement.

Additional Information:

• Item Code: JKA-230BM
• Pay Mode Terms: T/T (Bank Transfer)
• Packaging Details: Box Carton

Product Details:

Single Body Cremation Incinerator: TZ-230BC

• Dead Body Crematorium TZ-230BC

• LPG/ Diesel crematorium, Electric Heated crematorium, electrical Crematorium,
• Consists of a cremator- double chamber electric heated cremator chamber,
• Ash collection tray,
• Air blowers,
• Electric heater heated,
• Crematorium emissions management equipments,
• Instrument panel board,
• Incineration chamber temperature = 800 degree.
• Constructed with top quality aluminium oxide refractory bricks, with top quality castables, hearth clay and mortars Secondary chamber wherever the venturous gases and toxics and different volatile substances area unit fully burned.
• Electric loaded 16kw incineration.
• Cremation ashes dispose of time: inside three hours from the completion of a incineration. Cremation time per body: sixty to ninety minutes.

Note: image shown above is for illustration purpose only; Actual image may vary due to specification, Design, Technology and R&D.

Additional Information:

• Item Code: TZ-230BC
• Packaging Details: Box Carton

Product Details:

Item code: JKA-230SN

Sanitary Napkin Incinerator is the smallest incinerator. Sanitary products for personal hygiene, it incinerates un-hygienic pads/napkins.It commonly used in Girls Hostel, Girls Colleges, Ladies Toilets, Hotels, Malls etc. It is automatic sanitary napkin destroyer with high efficiency of reliability proven through performance.It is very useful for ladies toilets to get a pollution free hygienic environment.It destroys sanitary pads/napkins within few seconds and converted into a sterile ash.The incinerator reduces most combustible solid waste to nearly 2-3 percent by volume and 5percent by weight.
Specification:
Capacity: 5 / 10 / 20 / 25 50 / 100 / 150 / 200 Napkins per day
Power Requirement: Electricity
Smoke Control: Yes
LCD Display: Yes to capacity of 100, 150, 200 Napkins /day
Insulation: Ceramic insulation

Features:

• Wall mounted / Floor Mount
• Auto Power Off
• Burning process of Napkins produce less than 1 gm of ash per Napkin
• Ceramic Insulation for excellent thermal protection
• Auto thermal cut off for safety of user
• Very compact in size, can be mounted inside toilet
• Smoke control unit (100, 150, 200 Capacity) - [Optional]

Additional Information:

• Item Code: JKA-230SN
• Packaging Details: Box Carton

Product Details:

Mobile IncineratorJKA-230PM

A mobile incinerator is an incineration system mounted on a semi-trailer. Modern incinerators enable complete and sterile incineration of waste. They can be operated virtually anywhere.
A modern mobile incinerator unit (MIU) is capable of incinerating waste at a temperature of up to 1,200 °C (2,192 °F). This means, it is designed to incinerate all kinds of waste as well as infected hazardous waste. This satisfies the requirement that, waste of hospitals and health facilities must be burnt at a minimum temperature of 1,100 °C (2,012 °F) acc. to the rules of environmental protection. It can also be used to dispose of household waste, as a measure of environment protection.

Applications of mobile incineraor units

• Domestic waste
• Industrial waste
• Medical waste
• Cadaver or carrion of animals and
• Solid and paste-like chemical residues with moisture content

Product Details:

Domestic Waste Incinerator: JKA-230DW

Domestic waste incineration is the most advanced level of the waste disposal / treatment hierarchy: indiscriminate dumping, controlled dumping, landfilling, sanitary landfilling, and mechanical treatment. Solid waste arises from residential societies :- Baby diapers and adult diapers and so on.Incineration system provides an effective means of reducing the volume of Domestic waste. Domestic waste incinerator converts waste into ash Combustible gases at 1000°C in primary chamber Secondary Chamber temperature is raised upto 1450°C for at least 2 seconds to incinerate the wastes with a content of more than 1% of halogenated organic substances. The incinerator reduces most combustible solid waste to nearly 1-2 percent by volume and 3 percent by weight.

CONTROL
Fully automatic sequential control provided by internal PLC system providing control of :-

• Primary Chamber.
• Secondary chamber.
• Burn cycle (variable).
• Cool down cycle.

PRIMARY CHAMBER :-

• Fully insulated internal refractory lining constructed from high grade refractory brick ensuring a selfsupporting interlocked arrangement.
• Manually operated access lid.
• Waste ignition burner temperature controlled on-off complete with internal air fans.
• A pre-cast blocks impact zone that protects the refractory lining when loading.

SECONDARY CHAMBER :-

• Fully insulated internal refractory lining, constructed from high grade low thermal mass insulation.
• Secondary chamber burnout burner temperature controlled on-off complete with internal air fans.
• Integrated combustion burner air fans with automatically controlled distribution to their designated area.
• Temperature sensor mounting point of the chamber ensuring the chamber reaches the necessary temperature.

FUEL OPTIONS : Electrical/Diesel LPG
TEMPERATURES

• Main chamber : 850°C – can reach in excess of 1000°C
• Secondary chamber : 1000°C – 1450°C

BURNERS

• Fully automatic high-efficiency burners with electronic ignition, flame recognition and combustion control devices fitted.

CONSTRUCTION

• Mild Steel welded fabrication Consisting of sheet steel and structural section supports.

ASH REMOVAL

• Easy and safe manual ash removal from the primary chamber.

AVAILABLE LOADING CAPACITY : 10/25/50/100 Kg/Hr.

Additional Information:

• Item Code: JKA230DW
• Packaging Details: Box and Carton

Product Details:

Zero Fuel Incinerator
Salient Features of Zero Fuel Incinerator
We are among the most preferred organizations active in industry of Manufacturing and Supplying an exceptional variety of Zero Fuel Incinerator from Ambala, Haryana, India.

Product Details Zero Fuel Incinerator

• Automatic Grade Semi-Automatic
• Incinerator Type Portable Incinerator
• Capacity 30-60 kg/hr

Additional Information:

• Item Code: 17902
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

ELECTRONIC WASTE INCINERATOR : JKA-230EW

Design:

The design is based on the guidelines set by Central Pollution Control Board (CPCB)-India and normally adopted by military installation all over the country and worldwide. The Efficient power is supplied by electricity as well as oil burners for larger installation.

Specifications:

• Combustion efficiency 99%.
• Combustion Chamber : Dual Chamber
• Temperature of primary chamber is upto 1000°C and the secondary chamber is upto 1450°C.
• The secondary chamber gas residence time at is two seconds.

Power Requirement: Diesel, Electrical

** Note: The content of the product and specification are subject to change without prior notice for continuous improvement.

Additional Information:

• Item Code: JKA-230EW

Product Details:

Medical Incinerator with Conveyor: JKA-230MWC
Microteknik is the leading and successful Manufacturer and Exporter of Incinerators. we deals with Medical waste incineration involves the burning of wastes produced by hospitals, veterinary facilities, and medical research facilities.
Features:

• Robust construction.
• Virtually smoke and smell free with secondary burners.
• High temperature refractory lining.
• Quick heat up time and lesser operational time.
• Easy installation.
• Trouble free operation and maintenance.
• Designed to meet standards of central Pollution Control Board (CPCB).
• Available in oil, gas or electrically fueled.

Applications:

• Medical colleges.
• Hospitals.
• Nursing homes Institutions.

Additional Information:

• Item Code: JKA-230MWC

Product Details:

JKA-230KW
Kitchen waste incinerator to incinerates food scrap items such as vegetable and fruit waste,meal leftovers, coffee grounds, tea bags, stale bread, grains, and general refrigerator spoilage are an everyday occurrence in most hotels, restaurants, households etc. Their innovative design provides fast, efficient free burning of waste. The waste is loaded and ignited manually through the top loading door. The flames are fed with primary air from the holes in the cleaning door which flows up through the grill floor and the air intake cone. Once burning has started,secondary air is drawn from the underside of the hood, which causes intense secondary combustion for the efficient destruction of the smoke and gases, making the incinerators virtually smoke free.The kitchen waste incinerator reduces the original bulk by 99% into a light, sterile ash which falls through the grill floor into the ash collection pit. The ash only needs to be removed when it builds up and not after every burn. When the first load has burned down, more waste can beadded.

Specification:

• Applications: For Kitchen waste, food waste.
• Other Characteristics: Floor-standing
• Temperature range: Min. 850 °C (1562 °F) Max. 1150 °C (2102 °F)

Power Requirement: LPG, N-Gas, Diesel, Electrical

Capacity: 25, 50, 100 Kg

Temperature monitoring: Yes

Average ash residue (%): Upto 5%
Features:

• Virtually smoke free due to innovative design
• Low initial cost coupled with major disposal cost-saving
• Ready to use and does not require a pre-prepared base
• Reduce waste bulk to 3% to upto 5% which is collected in base

Additional Information:

• Item Code: JKA-230KW

Product Details:

Item code: JKA-230NS

We are leading manufacturers and suppliers of Napkin Incinerator with Scrubber. These are automated machines that switch off by themselves once the process gets over. The process takes very little time and results in a residue which is barely five percent of the input. The scrubber filters the exhaust stream. It is electronically operated and is highly power efficient. The machine is designed to provide long term service.

Features:

• Instant disposal of used Napkins in a very scientific and hygienic way.
• Front Opening Door with Automatic Door Closer.
• Inside SS covering for maximum lifetime, outside Mild Steel Metallic Spray Painting.
• The ash is collected in an Ash Collection tray.
• Just Start and Forget.
• It Burns and Stops Automatically.
• Complete burning of napkins only less than 5% ash per Napkin is Generated.
• Specially designed to destroy upto 20 napkins at a time.

Applications:

• Medical colleges Hospitals Nursing homes Institutions.
• Camp wastes Municipal wastes Girls Hostels Resorts/Hotels Malls/Shopping centers Girls colleges Colonies.

Accessories for Safety Purpose:

• Ceramic insulation for external thermal protection.
• Auto thermal cut off for safety of user.
• Having an emission outlet outside the room for the fumes.
• Developed during the incineration.
• Temperature and Timer display.
• Tripper for Emergency Power shutdown.
• Robust construction.
• Virtually smoke and smell free.
• High temperature refractory lining.
• Quick heat up time and lesser operational time.
• Easy installation.
• Trouble free operation and maintenance.
• Designed to meet standards of central Pollution Control Board (CPCB).

Construction with scrubber:

• Chamber in incinerators is built as per guidelines of CPCB.
• For large installations provided air Pollution control Device (APCD) like wet scrubbers.
• The body is made of steel and lined with high temperature Refractory that make our. Incinerators robust and trouble free for longer life.
• The construction is modular and individual components are easily assembled at site.

Specifications:

• Process: Fully Automatic and Electrically operated.
• Loading Capacity: Approximately 200 napkins per day.
• Duration to Destroy: Upto 15 minutes for 10 Napkins.

Additional Information:

• Item Code: JKA-230NS

Product Details:

Item code: JKA-230E

We offer a wide range of Electronic Biowaste Medical Incinerator which are manufactured using high quality materials as per industry standards. These Incinerators are built to the need of our customers to improve the environment to control hazardous solid caste. The incinerator reduces most combustible solid wastes to nearly 2-3 percent by weight. We design an build incinerators for specific needs Ibr specific wastes. Our Electronic Biowaste Medical Incinerator consists of electric heating elements.

Features:

• Robust construction
• Virtually smoke and smell free with secondary burners
• High temperature refractory lining
• Quick heat up time and lesser operational time
• Easy installation
• Trouble free operation and maintenance
• Designed to meet standards of central Pollution Control Board (CPCB)
• Available in oil, gas or electrically fueled

Our incinerators have following components:

• Primary Chamber
• Secondary Chamber
• Air Blowers
• Burners or electric heating elements
• Feeding Door
• Ash collection pit with ash tray (optional)
• Chimney

Construction without scrubber:

• Chamber in incinerators is built as per guidelines of CPCB
• The body is made of steel and lined with high temperature Refractory that make our Incinerators robust and trouble free for longer life
• The construction is modular and individual components are easily assembled at site

Applications:

• Medical colleges Catering wastes Resorts/Hotels Poultry
• Hospitals
• Nursing homes Institutions
• Industrial wastes Camp wastes Municipal wastes Malls/Shopping centers
• Animal farms like sheep kennels

Specifications:

• Temperatures: 1000 °C
• Material: Stainless steel
• Burn rate: 5 to 250 kg/hr

Additional Information:

• Item Code: JKA-230E

Product Details:

Item code: JKA-230P2

We are one of the leading manufacturers and suppliers of high quality Small Poultry Waste Incinerator. These products are uniquely designed to ensure total burnout of solid and liquid wastes. These products are designed to work with a wide range of fuels such as LPG, natural gas, and fuel oil. These products undergo various quality tests at each level of production, to ensure high standards of quality.

Being one of the most leading and prime companies in this line of work, we are availing our clients with one of the most exclusive kinds of poultry waste incinerators. These poultry waste incinerators are the giant machinery equipments which helps heat up and burn the waste items and degrade them to prevent any kind of pollution and Unhygienic. These poultry waste incinerators have been designed and constructed in most appropriate manner at our company which serves well for easy and quick incineration.

Features:

• Concave refractory bottom specifically designed to insure burnout and total destruction of solid and liquid wastes
• Insulated, refractory-lined chambers and stacks for durability, energy retention, and emissions control
• Secondary chamber with burner available
• Factory assembled, aluminized steel jacket lined with high temperature refractory
• High temperature refractory lined chamber walls
• Factory cured chambers and stacks
• Assembly on-site can be done with common farm equipment
• Counter-balanced fill door
• Manual set burn time and automatic shut off
• Choice of fuels: LP, Natural Gas, or Fuel Oil
• Burn times are adjustable by operator to meet varying loads
• Stack Test Data available on many models
• We provide permit and compliance assistance at no cost

Specifications:

Operation:

Additional Information:

• Item Code: JKA-230P2

Product Details:

Item code: JKA-230GC1

We offer economical Glass Crusher to our customers. This is manufactured using quality components. To supply only, manually fed, light diesel fuel, domestic incinerator with a capacity of not less than 600 kW capable of burning solid waste & sludge simultaneously, complete with automatic burner, flue gas pipe expansion compensator, pre-fabricated flue gas duct, motorized flue gas damper, ID fan & drive, free standing stub chimney etc. These products reduce the bottles to 20% their original size to glass grains with out any sharp edges. Complete with motor control center & all safeties.

Specifications:

• Voltage: 400 V.
• Phase: 3 Phase.
• Capacity: 800 Bottles per hour.
• Size: 700X660X400 mm.
• Daily service tank: 400 Lt.

Additional Information:

• Item Code: JKA-230GC1

Product Details:

Item code: JKA-230LA

Large Animal waste incinerators incinerate big dead animals like cow, pigs, buffalos, oxe etc.It is widely used to destroy to animal infection diseases, viruses and animal waste material.These products are manufactured using latest technology machinery.Large Animal Incinerator is double wall construction, duly insulated with high efficiency ceramic bricks, with dual chambers for complete combustible their dead bodies/carcass.The heating elements of these systems are made using nichrome wire. The chamber temperature is controlled by a PLC digital temperature controller.These products have separate doors for waste burning chamber and for ash collecting tray.A chimney is provided for emission of fumes. The incinerator reduces most combustible solid waste to nearly 2-3 percent by volume and upto 5% by weight.Large animal incinerator are easy to install and extremely durable equipment. It is available in varied capacity/sizes based on the requirement of Forest Department, Animal Industries andPoultry farms.

Characteristics:

Applications: for large animals, for animal waste

Other Characteristics: Floor-standing

Temperature range: Min. 850 °C (1562 °F), Max. 1150 °C (2102 °F)

Power Requirement: Diesel, LPG, N-Gas, Electrical
Capacity: 100, 200, 250, 500, 1000, 1300, 1500 Kg/Hr

Temperature monitoring: Yes

Average ash residue (%): Upto 5%

• Design and prepare the dead animal incinerator with dual chamber (Primary and Secondary

chambers) for complete combustion as per norms.

AVAILABLE LOADING CAPACITY: 100, 200, 250, 500, 1000, 1300, 1500 Kg/Hr.** Note:-The content of the product and specification are subject to change without prior notice for continuous improvement.

Additional Information:

• Item Code: JKA-230LA

Product Details:

SMALL ANIMAL INCINERATORS : JKA-230SA

DESIGN:

The design is based on the guidelines set by Central Pollution Control Board (CPCB)-India and normally adopted by military installation all over the country and worldwide. The Efficient power is supplied by electricity as well as oil burners for larger installation.

CHARACTERISTICS :

• Application: Floor-standing
• Temperature range: Min. 850 °C – Max. 1450°C
• Power Requirement: LPG, Diesel, Electrical
• Temperature monitoring : Digital Display
• Average ashresidue (%) : 3%
• Design and prepare the dead animal incinerator with chamber (Primary and Secondary chambers) for complete combustion as per CPCB Norms.
• Filration of smoke before releasing it in atmoshpare.

GENERAL CONSTRUCTION :

• Robust, Reliable and Efficient.
• Pre-fabricated 8 and 10mm robust mild steel casing, seam welded & suitably stiffened/braced where necessary.
• Paint finishing – The Mild steel structures are completely painted using a two pack high grade paint system that is baked into the steel structure at 70° C for 10 hrs.
• The layers of refractory lining in the primary and secondary chambers totaling of 230 mm. rated at 1450° C, provide increased fuel efficiency.
• Counter weight resilient refractory fiber insulation lid, Gives excellent thermal efficiency.
• Removable roof and back plate for ease of maintenance.
• All combustion fuel pipe work and electrical systems are weather proof and in accordance.
• Excess air and rapid cooling systems fitted as standard, aiding cleaner burns and faster cool down times.

** Note: The content of the product and specification are subject to change without prior notice for continuous improvement.

Additional Information:

• Item Code: JKA-230SA
• Packaging Details: Box & Carton

Product Details:

Poultry Incinerator : JKA-230PI
Specification:
Fully AutomaticTemperature range: Min. 850 °C (1562 °F) Max. 1150 °C (2102 °F)Power Requirement: LPG, N-Gas, Diesel, ElectricalLoading Capacity: 5, 10, 20, 25, 50 Kg/Hr.Duration to destroy: 20-30 minutes per batch.
Key Features:
Robust construction.Virtually smoke and smell free with secondary burners.High temperature refractory lining.Quick heat up time and lesser operational time.Easy installationTrouble free operation and maintenance.Designed to meet standards of Central Pollution Control Board (CPCB)Ceramic insulation for external thermal protection.
Accessories:
Auto thermal cut off for safety of user.Temperature and Timer display.Tripper for emergency power shutdown.

Additional Information:

• Packaging Details: Box Carton

Product Details:

Item code: JKA-230PM

Portable / Mobile Incinerator is one of the most effective waste treatment equipment applicablefor waste created by hospitals, medical, municipal, animal waste. This device is designed forquick and safe disposal as and where required.This system comprises of primary chamber.The combustion chamber is well insulated.The incinerator reduces most combustible solid waste to nearly 2-3 percent by volume and 5 %by weight.
Specification of Portable Mobile Incinerator
Heaters/Elements: Made of A-1 kanthal wire (14 gauge) for primary chamber & (17 gauge)for secondary chamber.Insulation: Multilayer insulation is done with combination of insulating bricks & siliconfiber insulating blanket to avoid any heat loss.Front Loading Type: It is portable/moveable in nature, which can easily place in a smallspace in a corner of building.

• Consisting of Dual Chamber: Works on thermal destruction using controlled combustion

chamber; combustion is controlled and provides enough heat to destroy the waste intodisposable state.

• Door: Fitted with hinges & handle for proper sealing to avoid heat loss.
• Temperature: Temperature of Primary/Burning chamber up to 850°C and for secondary

chamber 1000°C.

• Portable: Whole unit is mounted on sturdy wheels.
• Capacity: 5, 10, 20, 25, 50 Kg/Hr.
• Fuel Option: Diesel & Electrical

AVAILABLE LOADING CAPACITY: 5, 10, 20, 25, 50 Kg/Hr.** Note:-The content of the product and specification are subject to change without prior notice for continuous improvement.

Additional Information:

• Item Code: JKA-230PM

Product Details:

Item code: JKA-230MW

Municipal waste incineration is the most advanced level of the waste disposal / treatmenthierarchy: indiscriminate dumping, controlled dumping, landfilling, sanitary landfilling, andmechanical treatment. Solid waste arises from human activities- Domestic commercial,Industrial, agricultural, wastewater treatment, and so on.
Type of Waste:1. Domestic Waste: Waste from household activities, including food preparation,cleaning, fuel burning, old clothes and furniture, obsolete utensils and equipments,packaging, newsprint, garden wastes etc.2. Street Sweepings: The waste is dominated by dust and soil together with varyingamounts of paper, metal, and other litter from the streets. In lower-income cities, streetseeping may also include drain cleanings and domestic waste dumped along the roads,plant remains, and animal manure.3. Construction and demolition Waste: The composition of the waste depends on thetype of wood, packaging materials, and the like.
TEMPERATURES
Main chamber: 750°C – can reach in excess of 1000°C*Secondary chamber: 850°C – 1100°C*
BURNERS
Fully automatic, high-efficiency burners with electronic ignition, flame recognition andcombustion control devices fitted.
CONSTRUCTION
Steel welded fabrication consisting of sheet steel and structural section supports.
ASH REMOVAL
Easy and safe manual ash removal from the primary chamber.
Facility Including:

• Primary Chamber
• Combustion requirements
• Combustion control
• Air pollution control devices
• Anticipated air emission levels
• Noise control
• Monitoring
• Ash management

AVAILABLE LOADING CAPACITY: 5/10/20/25/50/150/200/250/500 Kg/Hr.** Note:-The content of the product and specification are subject to change without prior notice for continuous improvement.

Additional Information:

• Item Code: JKA-230MW

Product Details:

Item code: JKA-230RK

Specifications:

• Rotary Kiln (Rotataing Cylinder)
• Combustion efficiency is at least 99%.
• Combustion Chamber
• Temperature of primary chamber is minimum of 800°C-1500°C and the secondary chamber

is minimum 1200°C -1900°C.The secondary chamber gas residence time at least two seconds.Capacity: 500/1000/1500/2000 Kg/Hr.

• Air Pollution control device
• Wastes to be incinerated are not chemically treated with any chlorinated disinfectants.
• Ash from incineration of waste is disposed of at common hazardous waste treatment and

disposal facility. However, it may be disposed of in municipal landfill, if the toxic metals inincineration ash are within the regulatory quantities.

Power Requirement:

LPG, N-Gas, Diesel, Electrical

Additional Information:

• Item Code: JKA-230RK

Product Details:

JKA-230GC

Glass crushers are machines designed with the aim of crumbling glass to aid in the recyclingprocess. Glass crusher will handle a bulky glass waste and reducing volume by upto 80%. Thismachine crushes bottles very fast and safe–feed intake.Various sources of waste glasses in the form of bottles, glasses, glass sheets, jars etc., that canbe recycled with the help of the glass crusher. It is independently used by bars, hotels,restaurants etc.Glass Crusher is the ideal solution for companies requiring something to deal with largequantities of glass bottles, where storage and disposal are costly, and inconvenient.Glass crusher is built to quickly and safely reduce the size of glass bottles by up to 80%.
Glass recycling systems:
Specification:

• Noise Level: Low
• Constructed of heavy gauge steel

throughout

• Fast, efficient in operation with no

downtime problems.
GLASS CRUSHER
JKA-230GCPower Requirement: Electricity

• Reduce bottle volume by 5:1
• Reduces glass to cullet size
• Rated Capacity: 50, 100, 200, 300, 400,

500, 1000 kg.

Additional Information:

• Item Code: JKA-230GC

Product Details:

Item code: JKA-230PS

Plastic Waste Shredder is the advanced recycling technology, composting, that has undergonenumerous is based on natural biodegradation. For this reason, composting is used forprocessing waste with organic origin. Plastic is used and become waste; recycling process isapplied to return it to a usable product. Plastic waste shredder is recycling process that needsto have the right skill and equipment in order to perform.Any plastic waste or scrap has to undergo the following steps to be considered for recycling:
Step 1: Sorting/Separation - Plastics are many different types and it must be separated intodifferent types, plastic needs to be sorted after collection.
Step 2: Shredding - Once all the plastics are shorted from the waste plastic, the next stepinvolves shredded them into pieces. Shredding is done by a variety of tools and equipment thatis able to breakdown the waste plastic into small pellets.
Step 3: Extruding - The final stage is melting the plastic pellets on basic temperature whichhave been tested and approved. This is a process that involves a lot of energy consumption andmust be done using specific equipment. After completion of this process the plastic can berecycled and used to manufacture other products.
SPECIFICATION:
• All steel construction• conveyor hopper• 3/4 HP conveyor motor | 5 HP crushing motor• External tail-pulley adjustment• steel casters
FEATURES:
Solid body structure and casingLow noise level

• Heavy duty gear
• Maintenance gear
• Unit is protected against overloads and
• equipped with fuses
• Auto reverse features with PLC control
• (optional)
• Pneumatic feed control (optional)
• Low budget machine

AVAILABLE LOADING CAPACITY: 5/10/20/25/50/150/200/250/500 Kg.
** Note:-The content of the product and specification are subject to change without prior notice for continuous improvement.

APPLICATION:

• Finishing & Producing Industry
• Hospitals/Nursing homes
• Bio Medical Waste
• Laboratories
• Catering Industry
• Supermarkets
• Municipal Authorities
• Pharmaceutical Industry
• Plastic Industry
• Card Board Industry

Additional Information:

• Item Code: JKA-230PS

Product Details:

Item code: JKA-230EI

INDUSTRIAL INCINERATOR
Incineration uses combustion to make infectious industrial waste harmless and reduce thewaste mass and volume by more than 90 percent. Proper incineration can convert certainwastes into gases and incombustible solid residues (e.g., ash) that are relatively harmless. Adual-chamber incinerator operated within the optimal temperature range of 850° to 1200°Cresults in a lower level of emissions. The gases from incineration are released into theatmosphere (with or without gas cleaning). Residue ash from proper incineration can beencapsulated in designated ash pits or controlled landfills without any major risk. However,when the conditions are not adequate—for example, when the waste is not properly segregatedor the incinerator is not properly constructed or operated—toxic compounds can be found inthe unburned waste, and harmful gases can be released into the atmosphere. Good planning,technical oversight, and sustained supportive supervision of incinerator systems are critical toensuring safe incineration. Waste incineration plants is operated in such a way as to achieve alevel of incineration such that the total organic carbon content of slag and bottom ashes is lessthan 3% or their loss on ignition is less than 5% of the dry weight of the material.
INDUSTRIAL INCINERATOR
FUEL OPTIONS

• Diesel
• LPG
• Electrical

TEMPERATURES
Main chamber: 750°C – can reach in excess of 1000°C*Secondary chamber: 850°C – 1100°C*
BURNERS
Fully automatic, high-efficiency burners with electronic ignition, flame recognition andcombustion control devices fitted.
CONSTRUCTIONSteel welded fabrication consisting of sheet steel and structural section supports.
AVAILABLE LOADING CAPACITY: 100/200/250/500/1000/1500/2000 Kg/day** Note:-The content of the product and specification are subject to change without prior notice for continuos improvement

Additional Information:

• Item Code: JKA-230EI

Product Details:

Fully Automatic Organic Waste Converter TZ-240TECHNICAL SPECIFICATION:
OPERATION: Fully AutometicOUTPUT: Soil Conditioner/high calorific input for briquettes and pellets.INSTALLATION: Almost plug and play. Vent to be connected outdoors or strom water lines.No need of Water inlet. Water may be required, only to clean the machine externals and any spilled waste.CONTROL SYSTEMS: PLC Based-HMI is a(Variant)COMPOSTING TANK: SSHOUSING: M.S. with Powder Coating or SS panels as a VariantINPUT/OUTPUT: Door for Waste input, Separate door for getting out CompostHEATER: Insulated Oil heating Chamber or Heating pads as a VariantOTHER FEATURES :
Provided with waste overload function.Indicators for Power mode, heater & power saving mode.Stainless steel (SS304 ) shaft & mixing blades.Safety feature: Internal mixing blades automatically stop when output door is opened ( in auto mode).Can be run in auto mode or manual mode.Internal shaft turns and sends out the compost, when the compost door is opened (in Manual mode).

Additional Information:

• Item Code: TZ-240

Product Details:

Item code: JKA-230PW

We are manufacturer, supplier and exporter of a wide range of Plastic Waste Shredder which are manufactured using high quality materials. Pollution is a major issue caused by unsafe disposal of toxic & hazardous material. Since the materials like empty glucose bottles, hoses syringes, gloves etc. when burnt, emit gases, they have to be disposed of properly by using alternate safe methods. These when thrown are collected and resold in a new packaging, giving the impression of being fresh, resulting in the spread of deadly diseases. Our shredder is designed to avoid such instances and make the environment pollution free. The shredder shreds all kinds of waste like syringes, needles, glucose bottles, mineral water bottles, plastic lumps, pellets, wood paper, cardboard etc.

Features:

• Solid body structure and casing
• Low noise level
• Heavy duty gear
• Maintenance gear
• Unit is protected against overloads and equipped with fuses
• Auto reverse features with PLC control (optional)
• Pneumatic feed control (optional)
• Low budget machine

Application:

• Finishing & Producing Industry
• Hospitals/Nursing homes
• Bio Medical Waste
• Laboratories
• Catering Industry
• Supermarkets
• Municipal Authorities
• Pharmaceutical Industry
• Plastic Industry
• Card Board Industry

Specifications:

Additional Information:

• Item Code: JKA-230PW