Electrical Training Equipment

Product Details:

Distribution Transformer Trainer     MTS-855 

OC SC Test for three phase transformer with panel and transformer with digital panel meter display.

The Distribution Transformer Trainer, is a portable, hands-on trainer designed to allow students to develop competence in completing single/three-phase transformer connections similar to those performed in the North American power distribution system. The trainer contains two sets of three single-phase transformers to demonstrate three-phase banking configurations, such as wye-wye, delta-delta, closed delta-wye, closed wye-delta, open-wye, open-delta, and others. Each individual transformer winding is protected by a thermally-activated circuit breaker and designed to accept multiple faults.
The trainer is faultable in order to develop sound techniques for troubleshooting single-phase and threephase transformer banks. Eight (8) trainer faults are available.The trainer is complete with a student laboratory manual written in a skill-building, performance-based format, allowing easy set-up of all laboratory exercises.

Features & Benefits Distribution Transformer Trainer

• The trainer allows students to perform the following tasks:
• Identify different types of transformers
• Identify faulted transformers
• Test for proper no-load voltage

Show how a three-phase transformer produces correct and incorrect motor rotation Show how the ratio of the transformer windings affects the secondary output voltage Show how to simulate parallel single-phase and three phase transformers Simulate a burned-out transformer in a three-phase bank, and how to connect the remaining transformers in open-wye and open-delta configurations to produce the correct voltage
Topic Coverage

• Distribution Transformer Trainer
• Transformer Polarity and Terminal Markings
• Single-Phase Transformers Supplying Single-Phase Loads
• Single-Phase Paralleling
• Three-Phase Banking of Single-Phase Transformers

Product Details:

Electrical Engineering Teaching Equipment    MTK-8077

Scott Connection Trainer is an vital training system for the Electrical Laboratories. It provides comprehensive learning of Three Phase to Two Phase Conversion in a very simple manner. Study and Analyze the operation of Teaser Transformer and Main Transformer. Students can perform standalone operation and observe the two phase step down waveforms on oscilloscope, which will have 90° phase displacement with each other. The training system is engineered to be simple.

Features of Scott Connection Trainer:

• Stand alone operation.
• Exclusive and attractive designed panel.
• Designed by considering all the safety precautions.
• Main and Teaser Transformers are shown separately.
• On board high quality meters.
• Two phase step down outputs available for waveforms observation on oscilloscope.
• Provided with an extensive e-manual.
• Two years warranty.

Specifications of Scott Connection Trainer:

• Input Winding : 0 - 200 V (50%) ±10%, 50 Hz and 0 - 200 V (50%) ±10%, 50 Hz
• Output Winding : 0 - 230 V ±10%, 50 Hz

Teaser Transformer:
Input Winding :

• 0 - 115.6 V (28.9%) ±10%, 50 Hz
• 346.4 V (86.6%) ±10%, 50 Hz
• 400 V ±10%, 50 Hz

Meters Used:

• Voltmeter (MI) : 500 V (2 Nos.)
• Ammeter (MI) : 1 A (2 Nos.)
• Dimensions (mm) : W 600 X D 350

Other Details:

• Input : 415 V AC ±10%, 50 Hz
• Output Winding : 0 - 230 V ±10%, 50 Hz
• Step down Transformers (2Nos.)
• Input Winding : 0 - 230 V ±10%, 50Hz
• Output Winding : 0 - 18 V ±10%, 50Hz

Scope of Learning of Scott Connection Trainer:

• Study of Teaser Transformer.
• Study of Scott Connection.
• Three Phase to Two Phase Conversion.

Additional Information:

• Item Code: MTK-8077
• Production Capacity: 150
• Delivery Time: 1-2 weeks
• Packaging Details: Box Available

Product Details:

Training Equipment In Industrial Pneumatics     MTK-8078 


We offer industrial training for basic hydraulics, advanced hydraulics, basic will be created using our hands-on industrial grade hydraulic training equipment.Hydraulic training equipment and pneumatic training Equipment through to higher levels suitable for colleges, universities and industrial training centres.
Approx. dim: 1210mm(L) x 750mm(W) x 1450mm(H).The trolley must have two (2) circuit building plugboards (approx. size) 1100mm x 700mm, each with mounting holes must be fitted with rubber component retaining grommets.
The boards must be powder coated 16swg steel (at least), with 2mm shrouded sockets for electrical distribution built into the plugboard.

There must be two (2) lockable equipment storage cabinets, each consists of five (5) drawers (depths are 1 x 66mm, 2 x 85mm, 1 x 130mm, 1 x 200mm - approx. sizes). Cabinets and all drawers to be steel, powder coated construction including drawer fronts.

• The trolley must be mounted on four (4) heavy duty, rubber tyred castors two (2) of which are swivel and lockable.
• The trolley must be mounted on four (4) heavy duty castors two(2) of which are swivel and lockable. Set of Components

Pneumatics, comprises:

• 1 x Air service unit (filter/pressure regulator) with ON/OFF valve and pressure gauge
• 1 x 6-way manifold with check fittings (airflow blocked on removal of tubing)
• 1 x Single Acting Cylinder - 16mm diameter, 50mm stroke
• 2 x Double Acting Cylinder - 16mm diameter, 100mm stroke with magnetic piston for contactless sensing
• 4 x 3/2 way Push Button Valve (2 baseplates each with 2 valves)
• 1 x 3/2 way Toggle Lever Valve
• 1 x Visual Indicator
• 1 x 5/2 way Toggle Lever Valve
• 1 x 5/2 way Pilot/spring Valve
• 3 x 5/2 way Pilot/Pilot Valve
• 1 x 5/3 way Pilot/Pilot Valve with Closed centre
• 2 x 3/2 way Roller Lever Valve (for instroke operation) -mounted on adjustable baseplate (must have both vertical and horizontal adjustment).
• 2 x 3/2 way Roller Lever Valve (for outstroke operation) - mounted on adjustable baseplate (must have both vertical and horizontal adjustment).
• 1 x 3/2 way Adjustable Timer valve
• 2 x Throttle / Check Valve (on one baseplate)
• 1 x Quick Exhaust Valve
• 4 x Shuttle Valve / OR Gate (2 baseplates each with 2 valves)
• 2 x Two Pressure Valve / AND Gate (on one baseplate)
• 1 x Stainless Steel Air Reservoir
• 1 x Pressure Gauge
• 10 x Push-fit Tee
• 10 x Push-fit Plug
• 15 metres 4mm o.d. polyurethane tubing
• 5 metres 6mm o.d. polyurethane tubing

All pneumatic components should mount on four (4) pin plug-in baseplate, complete ready to use with pneumatic connections for 4mm o.d. tubing (supplied) and 2mm shrouded plugs / sockets for electrical connections. All threaded exhaust ports to be fitted with silencers.

Additional Information:

• Item Code: MTK-8078
• Production Capacity: 55
• Delivery Time: 2 WEEKS
• Packaging Details: BOX/CARTON

Product Details:

Power Distribution Board   MTK-3007 


Power Distribution Board should be specifically designed to suit theneeds of Electrical Laboratory Systems. Safety aspects are designedinto the system with high quality components through out for safe guardand protection to the operator.

Modules:

• The unit should allow wide flexibility to change the number of circuitbreakers and receptacles according the needs.
• The systems should include a range of 4 up to 12 receptacles, eachwith its own circuit breaker, that allow the user to connect electricalequipment directly to the board.
• This on-board design should consolidate all the essential componentsinto an easy to understand and operate system.
• The design should allow for extension boards to the bus bar ifneeded.
• The number of circuit breakers, receptacles, bus bars could bespecially ordered for custom requirements. In addition, components such as transformers or additional electrical meters,such as frequency meters or power factor meters, could be added to the system.
• The unit should be equipped with a Voltmeter and Ammeter to monitor the voltage and current in the lines.
• A direct-on-line push button start/stop switch should be provided for mains power control with safe guarded easyoperation.

Specifications of Power Distribution Board


1 Molded Case Circuit Breaker 160/600 A Overload and shunt trip coil
 1 Ammeter 100 A/5 A with selector switch
1 Voltmeter 500 V with selector switch
1 Earth Leakage Circuit Breaker (ELCB) 1 Frequency meter Power factor meter
1 Maximum demand indicator
2 Emergency stop button 1 Kwh meter,
3 phase 1 Kwh meter,
1 phase 4 Circuit breaker, 32 A, three phase 4 Circuit breaker, 6 A, single phase 4 Output socket, 5 pin (3 phase) 4 Output socket, 3 pin (single phase)
1 Set protective fuse 5 copper bus bar 0.25 inch x inch
 1 Set indicator lights
1 Set current transformer
 1 Set input socket, plug and cable 2 Compartments for storing made by heavy sheet steel finished baked epoxy powder with engrained and silk screen

Product Details:

Transducer Instrumentation Kit

Model No : MTK-3011 

The Sensor and Transducer Trainer is a modular training system which covers the theory, fundamental concepts and applications of sensors and transducers. The trainer should has many experimental modules covering a wide range various type of sensors and transducers including standard signals processing methods, which are required by many applications. The trainer should consists of base station into which a number of experiment modules can be fitted. A variety of modules should be available which extensively covers the topics of sensors and transducer.

Specification Transducer Instrumentation Kit:

A.Base Station The student base station serves as platform for carrying out the experiments. The experiment modules should be inserted into the base station and inter-connected to the services provided through 2 mm sockets and test leads. The base station should provide for all the primary needs of the experiment modules and includes a variety of components such as the following:Converter : 8 bit ADC/DAC Switches : 8 S P D T switches Amplifier : Instrument amplifier Potential meter : 2 Potentiometer Relays : Two 12 V DC relays DC Fixed Power : -5 V, 0, +5 V, -12 V, 0, +12 V DC Variable Power : 0 – 15 V DC Power Overload Indicator Input Voltage : 220/240 VAC, 1 phase, 50 Hz AC fuse and main power switch B. Experiment Modules
• Specialized Electronics Circuits. This should be consists of a set of several boards that covers aspects of specialized electronics circuits that are commonly required for the study of sensors and transducers. Topics and circuits should covered include Digital to Analog conversion,Analog to Digital conversion, Voltage to Frequency Conversion, Frequency to Voltage Conversion, Bridge Circuits, various filter circuits, signal amplifiers, signal conditioning linearization.
• Temperature Sensor Module Controlled temperature device with precision integrated-circuit temperature sensor which can be used to demonstrate aspects of temperature control as well as provide for a regulated load device for Temperature module.
• Proximity Sensor Module Rotational speed module with inductive proximity sensor which can be used to demonstrate aspect of speed control for rotational motion system
• Pressure Measurement Module. This module covers the main methods of measuring for pressure in various applications. Piezo resistor sensor which can use to read pressure of liquids and gasses
• Photo Electric Sensors Module These cover a wide range of devices that can be used for many applications. General photo/light sensor module which can be used to demonstrate aspects of light intensity control for automatic lighting system
• Position and Displacement Measurement Modules The modules are offered which are commonly used to detect position and displacement of objects. LVDT Transducer Module which can be use to indicate the linear position of a moving object
• Air Flow Sensors Modules These modules contain a variety of units that are common to the measurement of air flow.Consist of Differential Pressure Module and Paddle Wheel type Flow meter Module.

Product Details:

Operational Amplifier Trainer    MTK-8082 

Practical experience on this board carries great educative value for Science and Engineering Students.

List of experiments Following experiments can be performed:

• Basic operational amplifier circuit.
• Inverting amplifier.
• Non-inverting amplifier.
• Inverting A.C. amplifier.
• Non-inverting A.C. amplifier.
• High input impedance inverting amplifier.
• High input impedance non-inverting amplifier.

SOURCE FOLLOWERS OP- AMPS AS ANALOGUE COMPUTER ELEMENTS :

• Inverting summing amplifier.
• Non-inverting summing amplifier.
• Subtractor.
• Differential amplifier.
• A.C. differential amplifier.
• Adder subtractor.
• Multiplication by a constant.
• Division by a constant.
• Integrating amplifier for DC input signals.
• Integrating amplifier for AC input signals.
• Differentiator amplifier.
• Non-inverting differentiator.

FUNCTION GENERATOR :

• Sine Wave generator using wien bridge network Square Wave generator.
• Pulse generator.
• Square and Triangular wave generator.
• Saw tooth generator.
• Synchronised sawtooth generator with negative going pulse trigger.
• Synchronised sawtooth generator with positive going pulse trigger.

MULTI VIBRATORS :

• Astable multivibrator.
• Monostable multivibrator.
• Bistable multivibrator.

FILTERS :

• Low pass active filter High pass active filter Band, Notch filter.

VOLTAGE AND CURRENT REGULATOR :

• Basic reference voltage source.
• Basic reference voltage source with buffered output.
• Basic reference voltage source with negative output.
• Negative voltage reference source with buffered output.
• Positive regulator with variable buffered output.
• Negative regulator with variable buffered output.
• Buffered reference source.
• Basic non-inverting voltage controlled current source.

SIGN CHANGER :

• Sign changer with variable output.
• Switch select sign changer.

PHASE SHIFT CIRCUIT :

• Constant amplitude lag circuit.
• Constant amplitude lead circuit.

SIGNAL PROCESSING CIRCUITS :

• Diodes.
• Rectifier.
• Half wave rectifier.
• Full wave rectifier.
• Filtered full wave rectifier.
• Peak detector.
• Buffered peak detector.
• Inverting peak detector.
• Zero crossing detector.
• Buffered zero crossing.
• Clippers.
• Positive peak clipper.
• Negative peak clipper.
• Self buffered series clipper.
• Shunt clipper.
• DC restorer.
• Dead Band Response.
• Feed back circuit with dead band response.
• Variable dead band circuit.

LIMITERS :

• General purpose unipolar limiter, Bipolar zener limiter, Input current limiter, Diode bridge limiter using one zener, Adjustable bipolar limiter.

COMPARATORS :

• Fast precision voltage comparator.
• Single ended comparator with hysteresis & clamped feed back.
• Comparator for signals of opposite polarity.
• Comparator for A.C. coupled signals.

INSTRUMENTATION AMPLIFIER :

• Basic differential input instrumentation amplifier.
• Instrumentation amplifier with high input impedance.

Product Details:

Electrical Educational Distribution Trainer on Stand : 

Model no : MTS-856

Technical specification of Distribution Trainer :


Fundamental configurable distribution system for ring main or radial feeders with six tapping from either system or the facility to demonstrate the effect of varying the conductor cross section. AC and DC methods are available and two dual wound transformers included for AC demonstration. Both AC and DC variable power supplies range from 0 to 30 volts and the two transformers having 240 V winding.
0-300 v moving iron voltmeters 2 nos 0-30 v rectified moving coil voltmeters 3 nos 0-10 v rectified moving coil voltmeters 1 nos 0-1 A rectified moving coil voltmeter 11 nos Indication lamps to indicate volt drop in transmission line.
Three phase distribution consists of a three phase neutral distribution line with characteristics inductive and resistive features. Each phase line is represented by two separate sets of R and XL, and the neutral is to be divided in the same way.Each phase is to have a current transformer with the secondary taken to the terminals with protective relay. Three single pole protection relays of HV switch gear industry standard are to be included.

Product Details:

Hydraulics Training Equipment In Industrial     MTK-8079


Hydraulic trainer uses industrial-grade components to allow students to take an in depth look at how hydraulics works in the real world. The industrial hydraulic training program has a dedicated module that builds up a basic.

• The trolley having two (2) lockable equipment storage cabinets, each consists of five (5) drawers (depths are 1 x 66mm, 2 x 85mm, 1 x 130mm, 1 x 200mm - approx. sizes). Cabinets and all drawers are steel, powder coated construction including drawer fronts.
• The trolley having two (2) circuit building plugboards (approx. size) 1100mm x 700mm, each with mounting holes be fitted with rubber component retaining grommets, also fitted with receptacle for 1/4 turn aircraft fasteners to lock hydraulic components onto plugboard (for safety).
• The boards is powder coated 16swg steel (appx).
• Two (2) hydraulic power packs included, each being totally independent and can be used without interfering with the opposite side of the trolley.

• Each power pack have its own electric motor, pressure relief valve, return line filter, electrical start/stop control, oil level sight gauge, Filler/breather, drain port, reservoir capacity 10 litres usable (each), flow 3,5 litres per min @ 65 bar. Electric motor must be overload protected with automatic trip (resetable).
• Pressure and Tank manifolds is plugboard mounted, with test points for use with pressure gauges.
• The trolley is mounted on four (4) heavy duty, rubber tyred castors two (2) of which are swivel and lockable.]
• All hydraulic components and hoses be fitted with genuine leakage free, 'flat-face', quick-connect, self-seal couplings (male on valves, female on hoses).
• Except for in-line components all components must be fitted on plug-in baseplate with 1/4 turn locking fastener.
• Directional control valves is mini 3 with 3mm nominal bore, rated at 315 bar with 12 litres per min flow.
• Pressure control valves are series '0' with manual (knob) adjustment Set of Components - Hydraulics, comprises.
• 1 x Pressure Relief Valve [15] 3 x Pressure Gauge with Test Point Adapter - 50mm diameter stainless steel casing. [16] 1 x Flowmeter, 0 - 8 L/min (0,2 - 2,0 US gal/min) [17] 1 x Double Acting Cylinder 25mm bore x 200mm stroke (horizontal fitment) - with striker cam, have 2 connections and mini-mess test point on each port [18] 1 x 4/2 way Lever / Detent Valve [19] 1 x 4/3 way Lever / Detent Valve (Recirculating mid position) [20] 1 x Shut-off Valve with Graduated Scale [21] 2 x One-way Flow Control (Throttle/Check) Valves [22] 1 x 3-way Pressure Reducing Valve [23] 1 x Pilot Operated (Ventable) 2-stage, Pressure Relief valve [24] 1 x Bi-directional Motor - with 60mm diameter aluminium faceplate [25] 3 x Cross Tee with Test Point

Product Details:

Dual Output DC Power Supply      MTK-8081 

Dual Output DC Power Supply with Digital Display, Noise free output for servicing RF equipment, Fully isolated outputs for series or parallel operation, Coarse and Fine voltage controls.

Product Details:

Electrical Installation Trainer

Model No : MTK-3006

The Electrical Installation Trainer to provide students with a good foundation in electrical technology. The system must consists of a number of modules which are suitable for the study of electrical measurement, electrical installation and for the troubleshooting of electrical installations. Each module contains real electrical components such as contactors, switches, lamps, push buttons, timers, circuit breakers and relays. These modules can be arranged on the panel frame stand in a variety of configurations to make many different and interesting installations. Connections between the components or between the modules are made by using 4 mm test leads which plug into 4mm color coded heavy-duty binding posts. This will then allow the students to do the wiring quickly and with many variations. The trainer comes complete with laboratory manual which contains many experiments on electrical installation technology. Mobile training frame stands is available to mount the panels. Storage cabinets must be added to provide a convenient place to store the panel modules. Unit should be ungradable and have the ability for Inter connectivitybetween training systems in the teaching laboratory. Manual provided must clearly show the following educational topics of experiments are met. 

Experiment topics coverage : 

Residential Switches and Sockets Familiarization, Industrial Sockets and Plugs Familiarization, Special Purpose Switches,Lamps and Fitting Familiarization , Residential Electrical Installation, Intercom Installation, Door/ Bell Switch and Buzzer Installation, Controlling Single Lamp from Two Locations and Three Locations , Remote-Controlled Load Circuit, Timer-Controlled Lamp Circuit, Latching Relay Circuit, Three Phase Circuit- Voltage Measurement, Three Phase Circuit- Current Measurement.

Specifications Electrical Installation Trainer : 

The modules feature real industrial components that easily and securely fit into the training panel frames. , Special powder coated aluminum rails for plexi glass panels, which gives secure and firm fitting modules. Panels must be quickly arranged to conduct many experiments. All electrical connections for each component are brought out to 4 mm color-coded heavy-duty binding posts. Wiring from the component to the terminals is also color-coded. Interconnections between the panels and components are made via 4mm stackable test leads. Stackable test leads allow multiple connections from a single point, which is very useful when taking electrical measurements.Residential Switches:Mounted on Plexi glass panel with 4 mm terminals

• Switch, Surface mount, 1 way, 2 terminal, 10 A, 1 gang, (4 modules)
• Switch, Surface mount, 2 way, 3 terminal, 10 A, 1 gang, (4 modules)
• Switch, Surface mount, 2 way, 4 terminal, 10 A, 1 gang, (4 modules)
• Switch, Surface mount, Intermediate, 10 A, 1 gang, (4 modules)
• Switch, Surface mount,1 way, 2 terminal, 10A, 2 gang, (2 modules)
• Surface mount, 2 way, 3 terminal, 10A, 2 gang (2 modules)
• Switch, Surface mount, 2 way, 4 terminal, 10A, 2gang (2 modules)
• Switch, Surface mount, marked "Bell" (2 modules)
• Switch, Surface mount, illuminated (2 modules)

To include the sockets mounted onto panel with 4mm terminals, each socket is to include a matching plug

• 1 Phase Socket with switch, 13A, 3 prong, 1 gang (3 modules)
• 1 Phase Socket with switch, 13A, 2 prong, 1 gang (2 modules)
• 1 Phase Socket, with switch, 16A, 1 gang (5 modules)
• 1 Phase Industrial Socket, with cover, 16A, 2 Pole & Earth (2 modules)
• 3 Phase Industrial Socket, with cover, 16A, 2 Pole with neutral & Earth

Product Details:

Electrical Machine Trainer

Model No : MTK-3006

The Electrical Machine Trainer is designed to provide the students with agood and strong foundation in electrical machine technology. Thetrainer consists of modules and panels containing meters, variableresistors, resistive load, capacitive load, inductive load, motors,generators, and other supporting equipment which are suitable to studyvarious types of motors and generators according to theircharacteristics. The study of motors and generators covers the theory,design and characteristic of each motor and generator.Educational Objectives:

DC Machines Trainer Set :

Prime Mover & Torque Measurement. DC Motor Construction, DC Generator Construction. DC Shunt Motor Characteristic (starting, running, under load), DC Series Motor Characteristic (starting, running, under load). DC Compound Motor Characteristic (starting, running, under load). DC Separately-Excited Shunt Generator Characteristic (running, under load). DC Self-Excited Shunt GeneratorCharacteristic (running, under load). DC Compound Generator Characteristic (running, under load). DC Motor Starting Method Speed Control of DC Motor (requires optional power electronic module)Single Phase AC Machines Trainer Set Prime Mover & Torque Measurement Split-Phase Induction Motor Characteristic (starting, running, under load). Capacitor-Start and Run Motor Characteristic (starting, running, under load). Universal Motor Characteristic (starting, running, under load).Three Phase AC Machines Trainer Set Prime Mover & Torque Measurement Wound-Rotor Induction Motor Characteristic (starting, running, under load). Squirrel-Cage Induction Motor Characteristic (starting, running, under load). Synchronous Motor Characteristic (starting, running, under load). Three-Phase Alternator, Alternator Under Load, Alternator Synchronization, Alternator Power The Three-Phase Induction Motor Starters Rotary Frequency Converter

Description of modules :

AC/DC main power supply Mobile type trainer work station Universal motor DC multi function machine Single phase integrated induction motor Three phase slip ring motor with wound rotor 3 phase, 2 speed, pole changing induction motor with dahlander winding and squirrel cage rotor 3 Phase, synchronous machine with cylindrical rotor Three phase isolator switch Manual star delta switch Pole changing switch/selector switch Variable resistive load 1φ and 3 AC ammeters, AC voltmeters, DC ammeters, DC voltmeters Single phase/three phase watt meter Single phase/three phase power factor meter.

Product Details:

Motor- Generator System     MTK-3008

Motor and Generator/Alternator mounted into a special frame to accommodate coupling and electrical connections. All wiring connections from machine windings are brought out to 4mm terminals. Connection leads with banana plugs facilitate quick and easy connections between the Motor-Generator System and other controls. A fault insertion for machine winding is available as an optional item for student trouble shooting exercises.

Educational Objectives:

Induction motor as prime mover principles Saturation Curve of Generator/Alternator Balance Load Effect of Generator/Alternator Unbalance Load Effect of Generator/Alternator Open circuit, Short Circuit characteristics Voltage regulation in Generator/Alternator Losses and Efficiency in Generator/Alternator Troubleshooting Generator/Alternator system.

Specifications of Motor Generator System :

Power supply: 220/380 VAC, 3A.Power Indicator : indicate the incoming power at L1/R, L2/Y, L3/B.Power Control : Start Button, Stop Button, Emergency Button.Lamp Indicator : indicate run, overload and emergency condition on Instrument panel.Circuit Breaker : ELCB (Earth Leakage Circuit Breaker), MCB (Miniature Circuit Breaker).AC Voltmeter : Used to measure AC voltage.AC Ammeter : used to measure AC CurrentMotor Switch : used to connect-disconnect the motor with the power supply.Generator Switch : used to connect-disconnect the generator output to load.Generator Excitation : DC Voltmeter, DC Ammeter, DC MCB for short circuit protection, Excitation Switch, Excitation Control(%), Variable DC power supply (3 to 180VDC).
Generator.• DC Shunt Wound Generator,Alternators• 1 Ph. Alternator with Cylindrical Rotor, Stator Wound Rotor exited, 300VA
Motors:• DC Shunt Motor, 1 HP
• AC Three Phase Induction Motor, 1 HP
Accessories:
• 1 Set of test leads.
• Base plate machine bed with anti vibration rubber feet (bench top type) and protective cover.
• Student experiment manual.

Product Details:

Digital Application Trainer

Model No : MTK-3009


Digital Application Modules trainer should be designed to provide further and more extensive studies about some important digital circuits.The trainer should offers wide range of most common digital application circuits that are used in digital electronics. The trainer should consists of a number individual modules that could be used with the Digital Trainer Base Station. During the exercises, the student could make essential connections by using 2 mm stack able connection leads. In this way the student is able to construct and to complete the circuit in each of the practical exercises and students could take various electronic instrument measurements in order to under stand and to study the circuit electrical characteristics and behavior.

Modules & Course ware:

A comprehensive experiment manual should be provided to guide the students in studying the various application modules. This manual should include step-by-step instruction to prepare the modules for the experiment as well as some theory to strength en the student's knowledge in areas that is important as a background which is needed be fore doing the experiment.The application trainer should consist of the following modules and course ware respectively.a. Arithmetic Logic Unit The module should be able to perform AND, OR, Add, Subtract and perform binary operations. Uses 74181 I C that could be programmed which also use 7476 I C as data selector for the operations.b. Encoder & Decoder Application The module translates the 10 inputs generated form the switches to be inverted to B C D forms by the Encoder. The decoder then should be able to translate from B C D to 7 segment code which lights the proper segment on the output display.c. Data Transmission and Digital Switching Network System.The module could be use for sending and receiving serial data and are called multiplexers. It converts parallel digital data into serial then back to parallel.d. Frequency to Voltage and Voltage to Frequency Converter.The module should be a monolithic circuit designed for accuracy and versatility. It converts Voltage to Frequency or Frequency to Voltage.e. Analog to Digital Converter and Digital to Analog Converter The module should converts analog voltage into an equivalent digital signal and vice versa.The experiments that should be able to be facilitated by the modules are:
• Weighed Resistance Ladder Network Converter.
• R-2 R Ladder Network Converter.
• Fast 8-bit D A C.
• Fast 8-bit ADC.f. Breadboard Module The module should be able to be installed on the digital trainer base station. The module could be used for particular digital circuits or prototyping on some sections of the more complex digital circuits during practical applications or tests.

Product Details:

Electronic Tools Kit MTK-3015

Microteknik are offering a wide range of Electronic Tools Kit for Engineering training .
The Tools Kit Consists of:
• Utility component storage box
• Long nose plier 135mm
• Diagonal cutting plier 110mm
• Dual Color Lineman's plier
• Bent nose plier 130mm
• Side cutting plier 150mm
• Dual Color Long nose plier
• Reverse action tweezer
• 3pcs soldering aid tools
• Soldering iron stand with sponge
• Adjustable wrench 6"
• Ceramic soldering iron 220V
• Electronic Hex Nut Drivers, size 5mm
• Electronic Hex Nut Drivers, size 6mm
• Flat Tip (-) Screwdriver, 3.2 x 75mm
• Phillips (+) Screwdriver, #0 x 75mm
• Flat Tip (-) Screwdriver, 5.0 x 75mm
• Phillips (+) Screwdriver, #1 x 75mm
• Flat Tip (-) Screwdriver, 6.0 x 100mm
• Phillips (+) Screwdriver, #2 x 100mm
• Flat Tip (-) Pro-soft screwdriver, 6.0 x 40mm
• Phillips (+) Pro-soft screwdriver, #2 x 40mm
• Desoldering wick
• Brush
• 6pcs electronic screwdriver set
• Crimping tool (metric)
• Desoldering pump
• 5pcs needle file set
• Testing screwdriver
• Alignment tool (200mm/2.0mm)
• IC extractor
• Oil can
• Flash light
• 7pcs folding type hex key set (metric)
• 3 Prong holder
• 6pcs open-end wrench set
• Heavy Duty Curved-Claw Hammer
• PVC insulated tape
• Stainless scissors 6"
• Solder core 63%, SN
• Parts tube
• Heat sink
• Utility knife (3 blades self loading)
• Measuring tape 3M/10FT
• Inspection mirror
• Slip-channel pump pliers 254mm
• Pallet for tool kit
• Top pallet tool kit
• Carrying tool case

Product Details:

Soldering Station With Digital Display MTK-3016

Features Soldering Station With Digital Display

• Adjustable temperature and a variety of available tips.
• Grounded tip for soldering static sensitive devices.
• Overheat protection with closed loop temperature control.
• Improved circuit design for greater temperature stability.
• Heat resistant soldering iron cord.
• Built-in tray with cleaning sponge.

Specifications of Soldering Station With Digital Display

• Power Consumption: 48 W
• Temperature: 160 - 420 0C
• Voltage: 220 - 240 VAC/50 Hz
• Included with 3pcs replacement tips

Product Details:

Spectroscopy Experiment Kit   MTK-8087 

• Quick, accurate experiment.
• Big Base for providing stability during experiment.
• Made up of Brass Spindle & other critical components on CNC for precision accuracy.
• Smooth & frictionless motion of telescope collimator & venire scale.
• Robust instrument and the main structure is of heavy cast metal with bright plated fittings.

Product Details:

Spectrum Analyzer MTK-3026


Spectrum analyzers are widely used within the electronics industry to analysis frequency spectrum of radio frequency.

Specifications Spectrum Analyzer :
 
Center frequency display accuracy: ± 100kHz IF bandwidth (-3dB): 400kHz and 20kHz Sweep rate: 43Hz Amplitude range: -100dBm to + 13dBm Screen display range: 80dB (10dB/div) Reference level: -27dBm to + 13dBm (in 10dB steps) Distortion

Tracking Generator:
Output impedance: 50Ω (BNC) Radio Frequency Interference (RFI): <20dBc Output level range: -50dBm to + 1dBm

Product Details:

Dual Channel Oscilloscope MTK-3027 


The basic oscilloscope, as shown in the illustration, is typically divided into four sections: the display, vertical controls, horizontal controls and trigger controls. The display is usually a CRT or LCD panel which is laid out with both horizontal and vertical reference lines referred to as the graticule. In addition to the screen, most display sections are equipped with three basic controls: a focus knob, an intensity knob and a beam finder button.
Features
The oscilloscope is general purpose 100 MHz bandwidth, ideal forservice, education and production.• 100 MHz bandwidth, dual channel• sets memory for front panel setting save & recall• Cursor readout with 7 measurements• Panel setup lock of digital-control functions• Buzzer alarm• Trigger signal output• Z-Axis modulation input• SMD technology, high stability and reliability
Specifications
1. Vertical System:• Bandwidth: DC~100 MHz• Sensitivity: 2mV/DIV-5V/DIV, 11 steps in 1-2-5 sequence• Rise time : 3.5ns• Vertical mode: CH1, CH2, DUAL(CHOP/ALT), ADD, CH2 INV2. Horizontal System:• Horizontal modes: MAIN(A), ALT, DELAY(B)• Sweep time : 50nS~0.2S/div, continuously variable(UNCAL)• Delay time : 1us~5s3. Trigger:• Mode: AUTO, NORM, TV• Source: CH1, CH2, LINE, EXT• Coupling : AC, DC, HFR, LFR4. X – Y Operation:• X-axis mode: selectable CH1, CH2, EXT• Y-axis mode: selectable CH1, CH2, CH1 and CH2• Sensitivity: 2mV/DIV-5V/DIV• Bandwidth (-3dB): DC~500 kHz5. CRT:• Screen: 6” rectangular, internal graticule with % scale.• )

Product Details:

Master Electrical Tools Kit MTK-3024 


Microteknik are offering a wide range of Engineering Electrial Tool Kits.

Features of Electrical Tools Kit:

All the tools in this professional Aluminum tool case are speciallyselected for electrical engineers. It's a complete, professional andconvenient for repairing and installing quickly and accurately.

Specifications of Engineering Electrical Tool Kits:

The Tools Kit Consists of:

• Utility knife (3 blades self loading)
• Electrician's Scissors
• Led Flash light
• Adjustable Wrench - 8"
• PVC Insulated tape
• Contact Voltage Tester
• Lineman's Plier
• Side cutting Plier
• Long Nose Plier (165mm)
• Quick Heat Ceramic Soldering Iron 220V
• Slip Joint Plier 6"
• Slip-chamel pump plier 8"
• Pen Solder 63%
• Flat tip (-) Pro-Soft Screwdriver (3.0, 3.0x75mm)
• Phillips (+) Pro-Soft Screwdriver (#0, 3.0x75mm)
• Flat tip (-) Pro-Soft Screwdriver (5, 5x75mm)
• Phillips (+) Pro-Soft Screwdriver (#1, 5x75mm)
• Flat tip (-) Pro-Soft Screwdriver (6, 6x100mm)
• Phillips (+) Pro-Soft Screwdriver (#2, 6x100mm)
• Phillips (+) Pro-Soft Screwdriver (#2, 6x200mm)
• Heavy Duty Wire Strippers/Crimpers (206mm)
• Measuring Tape (5M/16FT )
• 9PCS Ball Point Long Arm Hex Key Set :Metric: 1.5, 2, 2.5, 3 , 4, 5, 6 , 8, 10mm
• 7Pcs Flexible Head Gear Wrench Set, Metric: 8, 10, 11, 13, 14, 17, 19mm
• 3-3/4 digits Auto range Digital Multi-meter
• Ball Peen Hammer with fiberglass handle
• Utility Component Storage Box (187.5x117x22mm)
• Plastic Pipe Cutter (6mm-25mm O.D (3/4",I.D) )
• All Purpose Snip
• Aluminum Frame Tool Case W/2 Pallet

Product Details:

CODE: MT-80033

·         1660 pt breadboard.

·         Logic probe with LEDs.

·         Clock generator with output frequency between 1Hz and 106 KHz.

·         Pulse generator: low/high and high/low moves.

·         Accessories include 2mm patch cords.

·         Power supply: +5 VDC, +12 VDC.

·         Digital trainer with 4-digit 7-Segment LED display.

Product Details:

·         CODE: MTS -4097T

·         The Integration System is ideal for demanding application projects. With its 1.2 kW fuel cell module, matching DC/DC converter and a software facilitating overall system control, training and research projects can be implemented easily.

·         The 1200 Fuel Cell Module is based on the FC Genâ„¢ 1020 ACS stack from Ballard. The system features a high system efficiency and superiour life expectancy for the stack. The robust housing protects the internal system components. All interfaces are provided on the back of the unit at one level. Integrated rails, the 19“ format and high flexibility with respect to the installation position and ventilation simplify integration of the system. The included start-up kit enables easy start-up of the system in the lab.

·         The Nexa® DC1200 transforms the nonregulated output voltage of the fuel system to 24/48 V DC voltage and enables battery hybridization. The Nexa® OSC Software can be used for efficient overall system control of the Nexa® 1200 and Nexa® DC1200. Data from all components can be centrally parameterized and visualized.

·         The fuel cell module, DC/DC converter and Overall System Control Software of the Nexa® Family are optimized for maximum compatibility. This enables fast and easy implementation of stationary applications.

Applications:-

·         Breadboard a ssemblies for fuel cell evaluation

·         Backup and emergency power supply

·         Small mobile applications

Product Details:

Item code: MTE-254EL

Laboratory experiments that serve experiment:

·         An educational lab which Combines new energy

·         Solar/photovoltaic, wind hydrogen Generation and fuel cell)

·         With Conventional power systems (battery bank and grid power,230 v)

·         the lab is integrated in a rack(except Solar panels and wind turbine)and comprises of the following components

·         Solar panels(photovoltaics): 1200 wp,

·         Wind generator(turbine): 400 wp ,

·         Fuel cell power module(air cooled, Wp 1200

·         Battery bank:55 ah, (Electrolyser (hydrogen generator(litters/hour(optional 60)

·         Metal hydride canisters: 1500 litters

·         Hydrogen storage capacity

·         Central energy management,

·         Module Controller with monitor and Educational software

·         Solar radiation and wind sensors

·         Electronic load 1, 5 kW.

Product Details:

Item code: MTS-859MG

Motor

·         Induction, 1500 RPM, 4-pole

·         Continuous duty, Class F insulation, open drip-proof

·         Selection of 50 Hz, 3-phase input voltages to include: 380V or 416V

Generator

·         Brushless synchronous, 1800 RPM, 4-pole

·         Continuous duty, Class F insulation, open drip-proof

·         Selection of 60 Hz output voltages to include: 120/208V or 277/480V, 3-phase Rated at 0.8 power factor to insure proper handling of inductive loads

Mechanical Construction

·         Motor and generator mounted on rigid steel base

·         Reduction gear drive system

·         Complete OSHA coupling guard

·         Forklift or pallet jack provisions

Standard Control Systems

·         Each motor-generator set is equipped with a separate free-standing control panel. The standard package includes the following components

Motor Controls

·         Motor starter with adjustable overloads

·         Start-Stop push buttons with terminal strip for remote start/stop

·         Control power transformer with fusing

·         Pilot light to indicate “Motor Run”

·         Pilot light to indicate “Reduction Gear Low Oil Flow

Generator Controls

·         Analog meter package to include voltmeter, ammeter and frequency meter

·         Voltmeter and ammeter phase selector switches (3-phase systems)

·         Voltage regulator, ±1% regulation accuracy, with automatic build up and rheostat for control of regulated voltage

·         Output circuit breaker, moulded case, to protect generator against short circuit or prolonged overload

·         Pilot light to indicate “60 Hz Load On

Product Details:

·         CODE: MT-80033

·         1660 pt breadboard.

·         Logic probe with LEDs.

·         Clock generator with output frequency between 1Hz and 106 KHz.

·         Pulse generator: low/high and high/low moves.

·         Accessories include 2mm patch cords.

·         Power supply: +5 VDC, +12 VDC.

·         Digital trainer with 4-digit 7-Segment LED display.

Product Details:

Item code: MTS-145PLC

·         The trainer has designed to work with most equipment that can be controlled by PLCS. It specifically work with the PLC trainers provided in this package.

Features of PLC Application Modules:

·         The system consists of a base station which provides a platform for the modules. The base station includes a number of switches, power supply and other control and signalling devices that can be used in conjunction with the modules for control, signalling or modification purposes. It features graphic representations of the device that they are simulating and use LED's to illustrate the actions that are taking place. The modules range from basic to intermediate levels in complexity. It provides practical programming applications for the student to work on and apply his new knowledge about PLC operations. These modular application modules allows immediate and easy use of PLC programming techniques and also the student may perform debugging procedures after watching the program run and correction errors.

Specifications PLC Application Modules:

 Base Station

·         The base station should have the following specifications:

·         The base station provides a platform and general facilities which the modules require for operation.

·         Contains a number of relays, switches, signalling devices, lights and buzzers which can connect to the application modules via 2mm stacking interconnect cables that are also included.

·         These switches and signalling devices allows the application simulation modules to operate and also provide some variables to the operation so that different characteristics could be explored.

Modules

·         Traffic Light Module

·         Objective: After completing this experiment, the students are expected to understand of using the TIM instruction in the Traffic Light operation programming application

·         Vehicle Parking Module Objective: After completing this experiment, the students are expected to understand of using DIFU, DEC, CMP, and MOVE instructions in the Vehicle Parking operation programming application.

·         Elevator Lift Module Objective: After completing this experiment, the students are expected to understand of using SET, KEEP, SBS, TIM, SBN and RSET instructions in the Elevator Lift operation programming application.

·         Laundry Module Objective: After completing this experiment, the students are expected to understand of using KEEP, SET, TIM, DIFU, CNT and RSET instructions in the Laundry operation programming application.

·         Bottling Plant Module Objective: Upon the completion of this experiment, the students will be guided to understand of using SET, TIM, and RSET instructions in the Bottling Plant operation programming application

·         Product Line Inspection Module Objective: After completing this experiment, the students are expected to understand of using SET, TIM, and RSET instructions in Product Line Inspection operation programming application

·         

Product Details:

·         CODE: MTS-860

·         Distribution Trainer. These are premium quality electrical equipments which facilitate ease of installation and maintenance. These equipments are highly demanded by electrical and electronic industries for varied purposes. These facilitate ease of installation and maintenance. Transformer Trainer demonstrates the principles of Lenzs first and second laws as applied to transformers. Typical material covered includes efficiency, ratios, vectors, open circuit test and short circuit test.

Specifications of Transformer Trainer

·         S1 x Single Phase Current.

·         1 x Three Phase Current.

·         1 x three phase voltage and current.

Low voltage power supplies

·         0-30V DC and 0-30V AC. Transformers: 2 x Low voltage single phase 150VA (one Step Up 30/240V and Other Step Down 240/30V. 1x line power 5KVA three phase star delta Dy11-reduces the incoming supply down. 1 x line receive 3KVA three phase star-delta Dy11with star point link to earth 220V/110V three phase. Includes tap section on its primary windings of 10%, 7.5%, 5%, 2.5%, and 0%. 220V Star connected Resistive, Inductive and capacitive. 110V Delta connected Resistive.

Product Details:

Item code: MTS-410LT

·         The Programmable Logic Controller is a PLC product which is powerful and flexible systems ideally suited to your specialized needs. The system should be compatible with a variety of accessories and peripheral, thus allowing this versatile system to be easily expanded into larger systems. The experiments should be chosen to cover the topics from basic familiarization of the PLC up to programming and application.

Courseware:

·         The trainer should cover the following topics of experiments:

·         Basic operation of PLC trainer

·         PLC software

·         Introduce the PLC hardware, such as: power supply, inputs, outputs and RS 232 communications.

·         PLC external I/O devices.

·         Timer circuit (functions of timer instruction in PLC)

·         Counter circuit (function of counter instruction in PLC)

·         Box conveyor (timer and counter application)

·         Keep instructions

·         Difu and Difd instructions, Difu and Difd application

·         Shift registers instructions

·         Overhead crane control application

Handheld programming console:

Specifications of Programmable Logic Control Trainer:

·         Trainer requirements

·         The unit should features a larger capacity compact PLC with approx. 40 I/O points.

·         The unit should be ideal to use with the applications board module for experimentation (using optional PLC application modules)

·         The set should include software for programming via a PC (PC is optional item).

·         Components PLC Trainer 24 V/2A DC load rating, approx. 24 input and approx. 16 output 40 point I/O with LED Indication. Computer programming software with ladder diagram. Main voltage: 220/240 VAC, 50/60 Hz. I/O: approx. 24 input switches, approx. 16 LED output indicators. 24 VDC Power supply

·         To come complete with comprehensive courseware.

Accessories

·         Set of connection leads.

·         Handheld programmer

·         2 analog input and 1 analog output extension module.

·         Experiment manual

Product Details:

Multifunction Counter     MTK-8080 

Features of Multifunction Counter

• Microprocessor to realize intelligent measurement;
• Low pass filter and attenuator in pre-position circuit;
• Count backwards, realize the equivalent accuracy
• measurement with fast speed and high sensitivity;
• Micro SCM to measure freq period and intelligentize the management;
• LSI design and CPLD application to diminish the components qty
• and the average working time be not less than 10000h without fault;
• Fine outline, small, light, easy to handle.

Specification ofMultifunction Counter:

Frequency measurement:
1Hz - 1.5GHz
1Hz - 3GHz
Cycle measurement:
10ns-1s
Count capability:
108-1
Input impedance:
Channel A 1MΩ//40pFChannel B 50ΩInput coupling mode AC
Waveform adaptability Sine, triangle, pulse
Dynamic of input voltage:
Channel A
30mVrms - 250Vp - p
Channel B
30mVrms - 1Vrms

Product Details:

Study of Differential Current Relay MTS-850 


Microteknik are leading manufacturer and Exporter Study of Differential Current Relay. Study of Characteristics of Over Current Relay, Study of Differential Relay, Study of Over Current & Earth Fault Relay.

Descriptions of Study of Differential Current Relay

• To study the characteristics of a Electromechanical Over current relay.
• To study directional over current relay.
• To study transformer differential protection.

The Current Differential/ Over current Relay provides protection for any two-input apparatus such as transformers, motors, generators, and reactors. Apply it for differential and over current protection and use event reports for quick post-event analysis.

Two-Winding Current Differential Protection


Sensitive current differential protection with programmable single- or dual-slope percentage restraint, supervised by the second- and fifth-harmonic elements for secure differential protection on two-winding apparatus. Choose from common or independent harmonic blocking or restraint. Unrestrained differential elements provide fast operation for high-magnitude internal faults. Automatic calculations of relay tap settings simplify application.
Individual Winding Over current Protection
Individual winding phase, residual, and negative-sequence over current elements, including instantaneous, definite-time, and inverse Time-over current elements for comprehensive over current protection.

Product Details:

Phase Sequence Detector and Indicator MTS-3023 Features of Phase Sequence Indicator Three function in one unit, including open phase, phase sequence andmotor rotation indication.

Product Details:

Multi function Counter MTK-3025

A versatile bench/portable frequency meter to be used for generalpurpose measurements. It should function as a Universal counter forfrequency, period, totalize self-calibrate.

Specifications Multi function Counter:

• Frequency Range: 1 Hz to 1.5 GHz.
• Period Range 10ns~1s.
• Totalize capability 108-1.

Sensitivity:

• 40mVrms (1Hz~10Hz).
• 20mVrms (10Hz~100MHz).
• 30mVrms (100Hz~1.5GHz).
• Input impedance 1M ohm/40pF(Channel A) 50 ohm (Channel B).

Input Voltage:

• 20mVrms~250Vp-p (Channel A).
• 30mVrms~1Vrms (Channel B).
• Couple Mode : AC.
• Time base stability : ±5 x 10-6/d.
• Power source: 220~240VAC±10%, 60Hz/50Hz.

Product Details:

Tap And Die Sets

Model no : MTK-3018 

Features ofTap And Die Sets :

Made from high carbon steel and should contains tapered adjusting screw, providing a range of tolerances for screw/nut matching.

Specifications of Tap And Die Sets:

Consist of 34 PCs. tap and die set in plastic box, consist of :

• m 3 x 0.5.
• m 3 x 0.6.
• m 4 x 0.7.
• m 4 x 0.75.
• m 5 x 0.8.
• m 5 x 0.9.
• m 6 x 0.75.
• m 6 x 1.0.
• m 7 x 0.75.
• m 7 x 1.0.
• m 8 x 1.0.
• m 8 x 1.25.
• m 10 x 1.25.
• m 10 x 1.5.
• m 12 x 1.5.
• m 12 x 1.75.
• 1/8 NPT 27 1 PC tap wrench (m 3 - m 12).
• 1 PC “T” type tap wrench. 
• 1 PC die stock 25 mm.
• 1 PC screwdriver.

Product Details:

Electric Hand Drill MTK-3019 


Specifications of Electric Hand Drill

•  No-load Speed:0-2800 rpm
•  Impact rate at no-load speed: 0-44800 bpm
•  Drilling dia. In concrete : 13 mm
•  Drilling dia. In steel : 10 mm
•  Drilling dia. In Wood : 1.5-13 mm
•  Robust and powerful 600W motor

Features of Electric Hand Drill

•  Extermely hand: no bigger than a glove and 1.7 kg light
•  Soft in live grip for a secure hold
•  Speed trigger with electronic control for exact pilot drilling
•  Rotating Brush plate rated ball bearing for long life
•  Auxiliary handle with depth stop for better control

Product Details:

Cold Light Source MTK-8042 

Technical Specifications of Cold Light Source:

• Model: single lamp / double lampoutput.
• Power: 250 watts (24 volts).
• Input: 180 vac - 270 VAC.

Features of Cold Light Source:

• S. M. P. S. Based design ensures smooth working of light source within the voltage variation of 180 -270 VAC.
• Half the weight & size of the conventional light sources.
• Light intensity controlled with smooth rotary potentiometer.
• Competitive rates, efficient service backup of india.

Product Details:

Three Arm Puller Sets MTK-3020 


These three-jaw pullers are made of forged alloy steel to give you over a ton of pulling power! The three-jaw puller set includes 3 in., 4 in., 6 in., 8 in. pullers with reversible jaws to ensure proper grip on a wide range of jobs. A chrome finish helps resist rust and corrosion, making this an ideal puller set for the home or shop.

Specifications Three Arm Puller Sets :

• Forged alloy steel.
• Rust resistant chrome finish.
• Reversible jaws for inside and outside pulling.
• Includes 3 in., 4 in., 6 in., 8 in. pullers.

Product Details:

·         POWER SUPPLY MCPS-102PS

·         Cooling: Air Cooling

·         Maximum Spike Current (A): 5 A

·         Minimum Output Power (V): 2 V

·         Maximum Output Power (V): 12 V

·         Accuracy (%): 99 %

·         Dimensions (W x H x D): 190 x 190 x 110 mm

·         Weight: 1-2 kg

Product Details:

Item code: MT-474TC

·         We are manufacturer and Exporter of Electrical Engineering training Equipment for engineering colleges.

·         Laboratory experiments that serve the items listed.

·         Power supply with at least fixed 3 phase 380 vac, fixed 220 v dc and variable.0-380 v. three phase and 0-230 v dc,5 a. the power supply must contain a centre taped transformer.

·         All power electronics components piv and 5 a.

Product Details:

Item code: MTS-880

Modular Power Hub

·         We are manufacturers of finest Modular Power Hub in India and also supplies and exporters Modular Power Hub around the world at best prices. To enquiry Modular Power Hub, please fill below form. We'll be back with you

Feature:

·         DC power cord application eliminates the use of the extension cord keeping your server room neat

·         Front panel LEDs indicate the real-time power consumption

·         Fool-Proof plugs, avoid short-circuitry

·         Provide 8 extra power source for the connected devices

·         4 DC receptacles on the front panel plus 4 DC receptacles on the rear panel make connections easy to reach

Product Details:

·         CODE: MPH-EE-56

·         A simple model of a DC electric motor, having a 2-pole armature wound with enameled copper wire on an insulated plastic bobbin.

·         The magnetic field is provided by a removable permanent magnet.

·         The model is completely open with all components easily identifiable and clearly observable.

·         A disc-type commutator is incorporated and external connection to the phosphorus bronze bushes is by means of a pair of 4mm colour coded sockets.

·         The motor operates on 6-8 volts DC.

Product Details:

·         CODE: MT-775LM

·         Made of brass alloy heavy duty and polished.

Size:

·         37x25x15 mm pair.

·         50x25x15 mm pair.

·         75x30x19 mm pair.